I seem to have lost a rare and unique part. Ive had my carbs off the bike for some time now and a few garage clean outs and repositioning of my bikes over time have resulted in me miss placing the carb choke lever connecting rod.
I was wondering if anyone has a spare which I could buy.
I could make one from a piece of welding rod but ide rather buy a genuine one first before i go down that route.
regards stupot
wanted T500 choke connecting rod
-
- Posts: 128
- Joined: Tue Jun 10, 2014 5:26 pm
- Location: under bridge J22 M60
wanted T500 choke connecting rod
everyones a winner
- itsnotateapot
- Posts: 1179
- Joined: Thu Feb 16, 2012 10:09 pm
- Location: Sheffield, South Yorkshire
Re: wanted T500 choke connecting rod
Hi Stu, use a small spoke its all ready bent at one end.
click on picture to enlarge
click on picture to enlarge
SUZUKI GT750 L
SUZUKI T500 M
SUZUKI GT185 K
Suzuki T500 Cobra
Suzuki GTS 500 Hybrid.
Suzuki RG250.
SUZUKI T500 M
SUZUKI GT185 K
Suzuki T500 Cobra
Suzuki GTS 500 Hybrid.
Suzuki RG250.
-
- Posts: 128
- Joined: Tue Jun 10, 2014 5:26 pm
- Location: under bridge J22 M60
-
- Posts: 128
- Joined: Tue Jun 10, 2014 5:26 pm
- Location: under bridge J22 M60
- Eastham
- Posts: 86
- Joined: Tue Oct 27, 2020 4:42 pm
- Location: Guernsey
Re: wanted T500 choke connecting rod
How small is small, I’ve got loads off my Fizzy, your more than welcome to have a few
-
- Posts: 128
- Joined: Tue Jun 10, 2014 5:26 pm
- Location: under bridge J22 M60
Re: wanted T500 choke connecting rod
Sorry for the long tine in replying ive been drinking with my mates in Lytham st Annes for the weekend.
Ive just got back , I knew you had replied with your kind offer seeing it on my moblie but i couldnt acknowledge because i dont know my password for this forum.
YES Please I will send you PM with my details.
Im sure thats the correct gauge but as my Verneir Calopian Giggly tump is imperialistic and not even digitdlium then I used my rule of thumb to asses the correct DIA and yes its going slide into position perfectly.
Best regards Stupot.
Ive just got back , I knew you had replied with your kind offer seeing it on my moblie but i couldnt acknowledge because i dont know my password for this forum.
YES Please I will send you PM with my details.
Im sure thats the correct gauge but as my Verneir Calopian Giggly tump is imperialistic and not even digitdlium then I used my rule of thumb to asses the correct DIA and yes its going slide into position perfectly.
Best regards Stupot.
everyones a winner
- Eastham
- Posts: 86
- Joined: Tue Oct 27, 2020 4:42 pm
- Location: Guernsey
-
- Posts: 128
- Joined: Tue Jun 10, 2014 5:26 pm
- Location: under bridge J22 M60
Re: wanted T500 choke connecting rod
Hi Neil. Your spokes arrived today and ive allready tried one and it fits perfectly so thankyou your very kind .
ive been tinkering with the carbs, I know how its been miss placed , some how ive ended up with two left choke lever assemblys , so somewhere in the world someone will have two right hand choke assemblys LOL.
Luckily i have a spare set of carbs and ive managed to swap the correct left and right levers onto the carbs im using and with the missing rod spoke now supplied i will have a full set.
ive been tinkering with the carbs, I know how its been miss placed , some how ive ended up with two left choke lever assemblys , so somewhere in the world someone will have two right hand choke assemblys LOL.
Luckily i have a spare set of carbs and ive managed to swap the correct left and right levers onto the carbs im using and with the missing rod spoke now supplied i will have a full set.
everyones a winner
- Eastham
- Posts: 86
- Joined: Tue Oct 27, 2020 4:42 pm
- Location: Guernsey