setting ignition timimg
-
- Posts: 495
- Joined: Tue Sep 26, 2017 10:27 pm
setting ignition timimg
i can t seem to line up when the points open with the timing line on my 750a , whichever way i move the timing plate its not having it ! this was after the starter clutch boss nut came loose , any ideas please
-
- Posts: 128
- Joined: Tue Jun 10, 2014 5:26 pm
- Location: under bridge J22 M60
Re: setting ignition timimg
I understand the question but i dont understand what your doing. your description of your issue sounds a bit like stanley unwin.
are you using a bulb to set static timing ?
Or is the bike running and your using a strobe ?
Is it electronic ignition ?
are you using a bulb to set static timing ?
Or is the bike running and your using a strobe ?
Is it electronic ignition ?
everyones a winner
-
- Posts: 495
- Joined: Tue Sep 26, 2017 10:27 pm
Re: setting ignition timimg
bulb to set static timing and its on points !
- canaletto5
- Posts: 5228
- Joined: Tue Jul 23, 2013 8:43 pm
- Location: Derbyshire
Re: setting ignition timimg
Terry
The starter clutch won't affect it.
Have you set the points gap first?
Assuming that you are turning the engine the right way, (Use the kickstart to move it), then it is possible the heels on the points cams are worn. When were they last replaced? Also, some aftermarket points are frankly crap and also don't allow proper set up.
Kev
The starter clutch won't affect it.
Have you set the points gap first?
Assuming that you are turning the engine the right way, (Use the kickstart to move it), then it is possible the heels on the points cams are worn. When were they last replaced? Also, some aftermarket points are frankly crap and also don't allow proper set up.
Kev
-
- Posts: 495
- Joined: Tue Sep 26, 2017 10:27 pm
Re: setting ignition timimg
cheers Kev , i ll check that
-
- Posts: 1035
- Joined: Mon Mar 07, 2011 8:10 pm
- Location: Chicago
Re: setting ignition timimg
Let's address the starter clutch thing first. If the key is in place, the points cam is mechanically tied to the crank in the correct orientation. That said, sometimes the key is pushed out of place and when the starter clutch is tightened it can be out of position.
If the timing looks to be more than a couple of degrees out, I would open that side up again, remove the starter clutch and be 110% sure the key is in there.
If the timing is only out by say 5-10 degrees, it is probably the propeler out of place. Either the pin is missing or more common, it's sloppy fit and was tighetened up out of place.
If the points are worn, it may be hard to get the timing and gaps right, and as someone mentioned, some aftermarket points are a misformed and make it impossible to set the timing.
If the timing looks to be more than a couple of degrees out, I would open that side up again, remove the starter clutch and be 110% sure the key is in there.
If the timing is only out by say 5-10 degrees, it is probably the propeler out of place. Either the pin is missing or more common, it's sloppy fit and was tighetened up out of place.
If the points are worn, it may be hard to get the timing and gaps right, and as someone mentioned, some aftermarket points are a misformed and make it impossible to set the timing.
-
- Posts: 128
- Joined: Tue Jun 10, 2014 5:26 pm
- Location: under bridge J22 M60
Re: setting ignition timimg
dirty points faces I give them a quick rub with 600 wet and dry.
everyones a winner
- canaletto5
- Posts: 5228
- Joined: Tue Jul 23, 2013 8:43 pm
- Location: Derbyshire
- Bikesklade
- Posts: 7
- Joined: Sat May 15, 2021 9:16 am
Re: setting ignition timimg
My Starter clutch came loose, stripped the keyway in the process and the timing ended up 180 degrees out. Only found that was the case when I used a DTI to check the timing .
New key, reset the points gap and opening point using a volt meter and the bike now runs like a top.
I suggest you check the keyway
Kevin
New key, reset the points gap and opening point using a volt meter and the bike now runs like a top.
I suggest you check the keyway
Kevin